SBAT111 Postad 6 April , 2015 Rapport Share Postad 6 April , 2015 Since I have been asked abuot this a few times and understand that it may be difficult for non-Swedish speaking people to follow the discussions in our forum I thought I would try a simple summation of the matter.The automatic transmission for Scania TGB30 / 40 is relatively easy to operate manually (with electric voltage). The easiest way is to locate the electrical connection piece to the right in the fuse panel located at the dashboard (see picture). This connectionpiece contains all the cables required for control of the gearbox(cables number 18, 18A, 503, 521, 522, 523 and cable number 526).Connect power to the cables for the gearbox according to the schedule at the top right of this wiring diagram.You can obtain the connectionpiece from ELFA (https://www.elfa.se/elfa3~se_sv/StartPage.do?ignorecookie=true) part no.44-221-04 https://www.elfa.se/elfa3~se_sv/elfa/init.do?sq=44-221-04&cat=0 and the contaktpins part no.44-221-13 (https://www.elfa.se/elfa3~se_sv/elfa/init.do?sq=44-221-13&cat=0) 7 Citera Länk till kommentar Dela på andra webbplatser More sharing options...
bandar Postad 20 Maj , 2015 Rapport Share Postad 20 Maj , 2015 dear friend can i get your phone number i have question about gear transmission for speed or to send me sms on +974-33339696 Citera Länk till kommentar Dela på andra webbplatser More sharing options...
SBAT111 Postad 20 Maj , 2015 Författare Rapport Share Postad 20 Maj , 2015 I think it would be best if you stated your question here on this page, mabye illustrated with pictures since there are a lot of people with wast experience of the gearbox on this forum. Citera Länk till kommentar Dela på andra webbplatser More sharing options...
SBA111 Postad 20 Maj , 2015 Rapport Share Postad 20 Maj , 2015 bandar, replying to your PM question about why the gerbox does not change to higher than H3. First thing, check that the brake light is not always on, check that the trailer brake lever under the left part of the steering wheel is fully up/forward. Citera Länk till kommentar Dela på andra webbplatser More sharing options...
bandar Postad 20 Maj , 2015 Rapport Share Postad 20 Maj , 2015 SBA111 thank you . May I have in contact with you to clear this issues regarding the gear transmission . My Mobil no . +974-33339696 Citera Länk till kommentar Dela på andra webbplatser More sharing options...
bandar Postad 20 Maj , 2015 Rapport Share Postad 20 Maj , 2015 Or what,s up Citera Länk till kommentar Dela på andra webbplatser More sharing options...
bandar Postad 20 Maj , 2015 Rapport Share Postad 20 Maj , 2015 Or what,s up Citera Länk till kommentar Dela på andra webbplatser More sharing options...
kristaga Postad 20 Maj , 2015 Rapport Share Postad 20 Maj , 2015 974 is the country code for Qatar. Since it might be very expensive to call Qatar I advise you (as SBAT111 also says) to state your questions here at the forum. Citera Länk till kommentar Dela på andra webbplatser More sharing options...
bandar Postad 20 Maj , 2015 Rapport Share Postad 20 Maj , 2015 I will call just mised call & I will call .it is difficult to explan in writing Citera Länk till kommentar Dela på andra webbplatser More sharing options...
bandar Postad 20 Maj , 2015 Rapport Share Postad 20 Maj , 2015 When I drive the truck it change up to three speed with 40km . I could not go for more speed or change the gear to more . What should I do Citera Länk till kommentar Dela på andra webbplatser More sharing options...
bandar Postad 22 Juni , 2015 Rapport Share Postad 22 Juni , 2015 dear freinds how can i reach maximum speed of scania sbat 6x6 Citera Länk till kommentar Dela på andra webbplatser More sharing options...
Wingflyer Postad 22 Juni , 2015 Rapport Share Postad 22 Juni , 2015 It sounds like your transfer box might be stuck in low gear (T). Citera Länk till kommentar Dela på andra webbplatser More sharing options...
bandar Postad 22 Juni , 2015 Rapport Share Postad 22 Juni , 2015 how can i know . and to solve it Citera Länk till kommentar Dela på andra webbplatser More sharing options...
bandar Postad 22 Juni , 2015 Rapport Share Postad 22 Juni , 2015 is there any switch to be pressed Citera Länk till kommentar Dela på andra webbplatser More sharing options...
SBAT111 Postad 22 Juni , 2015 Författare Rapport Share Postad 22 Juni , 2015 The rear switch that is marked V and T should be in position V (road)! Also check that the indication light for frontweeldrive (framhjulsdrift) is turned of. With the engine turned off you should be able to hear the sound of the magnetic valve when changeing from V to T and back. The controlbox just sends a momentary puls on lead 527 to engage V and 528 to engage T. 2 Citera Länk till kommentar Dela på andra webbplatser More sharing options...
bsvensso Postad 23 Juni , 2015 Rapport Share Postad 23 Juni , 2015 Sounds like the throttle pedal switch may be blocking the V-T signals? 2 Citera Länk till kommentar Dela på andra webbplatser More sharing options...
bandar Postad 23 Juni , 2015 Rapport Share Postad 23 Juni , 2015 thank you all . I will check & let you know . 2 Citera Länk till kommentar Dela på andra webbplatser More sharing options...
bandar Postad 2 Juli , 2015 Rapport Share Postad 2 Juli , 2015 i have checked all of the above but still same problem the gear changing upto three with 60 km . it canot move more . do you think the problem from the auto transmision controll unit which undernith the gear swithch ( aluminum box ) ? Citera Länk till kommentar Dela på andra webbplatser More sharing options...
Wingflyer Postad 2 Juli , 2015 Rapport Share Postad 2 Juli , 2015 If you know a little about electrical circuits, etc., you may try with a manual switch between +24V and wire number 524 in the connector block in the picture above. When driving the truck in 60 kmh, flipp the switch so you get 24V on 524. The gearbox should then change to 4'th gear (M3). If it does, your problem is in the control unit. If not, the fault is in the gearbox or the electrical harness... 1 Citera Länk till kommentar Dela på andra webbplatser More sharing options...
Halfsafe Postad 2 Juli , 2015 Rapport Share Postad 2 Juli , 2015 Make sure you have not mixed up the relays in the relay box. There are 2 different types that look the same but have different function. Make sure they work and are in their correct position. Citera Länk till kommentar Dela på andra webbplatser More sharing options...
bandar Postad 2 Juli , 2015 Rapport Share Postad 2 Juli , 2015 thank you all. what do you mean by flipp the switch and which switch ? Citera Länk till kommentar Dela på andra webbplatser More sharing options...
Halfsafe Postad 2 Juli , 2015 Rapport Share Postad 2 Juli , 2015 Here are the positions of the relays: Make sure A and B relays are not mixed up. If I remember correctly they look like this: 1 Citera Länk till kommentar Dela på andra webbplatser More sharing options...
bandar Postad 2 Juli , 2015 Rapport Share Postad 2 Juli , 2015 i will check & come back soon Citera Länk till kommentar Dela på andra webbplatser More sharing options...
Wingflyer Postad 2 Juli , 2015 Rapport Share Postad 2 Juli , 2015 thank you all. what do you mean by flipp the switch and which switch ? This is why I asked if you are familiar whit electric schematics and circuits. You can insatall an extra switch as described, and thus manually test the gearbox fouth gear... Citera Länk till kommentar Dela på andra webbplatser More sharing options...
tbw Postad 8 Februari , 2016 Rapport Share Postad 8 Februari , 2016 Hello all. We have a problem, we bought such military truck from the army and the truck was working flawlessly until now. We have sold the truck, and today morning the customer has driven the truck to another place and left it there. In the afternoon the guys from that place wanted to move the truck but it is not moving when switched to D. The terrain and street switch is on V. Before when you put it into drive you could feel that the truck started to move a bit, now nothing happens. Please help. Could this be an electrical problem. We have checked automatic transmission oil, while the engine was running and the level is good. I tried to lift the back axels, because I thought that the truck is stuck between street and off road gears, but it is not. Need your help. I doubt that the gearbox went bad on an empty truck, because it was working in the morning, and in the afternoon it does not do anything. Thanks. Citera Länk till kommentar Dela på andra webbplatser More sharing options...
Rekommendera Poster
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.