Gå till innehåll

Glynn

Sergeant
 Visa profil  Visa deras aktivitet

  • Innehålls Antal

    116

  • Gick med

  • Besökte senast

 Innehållstyp 

Allt postat av Glynn

  1. Glynn
    Has anyone any info about fitting a b30 or b36 into a sugga. What length is a b30? Is it too long? Any problems? Thanks
  2. Glynn
    i verkstadshandboken står det att dra bort det med lageravdragare. det är mycket snäv
  3. Glynn
    vattenpump. bör detta vara en platta? Hårt slitna jag tror
  4. Glynn
    Sugga har inte fram indikatorer ursprungligen. Jag ändrade några fram blackout ljus, skär toppen av och monteras klassiska indikatorer i dem. ledsen har bilder inte.
  5. Glynn
    Xcs49 points Xd138 dist cap Xr152 rotor arm These are from a Mercedes and are quintin hazzel part numbers but search and you will find them. I haven't found a direct replacement for the condenser if anyone knows of one?
  6. Glynn
    Hi all does anyone live near lierskogen in Norway? I need to find a friendly transport company there that could collect an engine for me. Hei alle Er det noen som bor i nærheten av Lierskogen i Norge ? Jeg trenger å finne et vennlig transport selskap der ute som ville samle en motor for meg .
  7. Glynn
    Hi folks Does anyone know what the bearing crush on the big end is for the ED engine? Thanks
  8. Glynn
    Between drivers seats with mt920 plugged in!
  9. Glynn
    They have an accelerator pump which can leak and also a small brass plunger which sticks. Repair kits are available in the USA. Is the problem when accelerating only?
  10. Glynn
    Is anyone going to this auction ? I am interested in the Volvo fire pump ,could someone bid for me? Thanks Hej, någon kommer att detta vara? Jag är intresserad av volvo brandpump . skulle någon bjuda på mig ? tack
  11. Glynn
    Hi I am looking for a sugga engine or parts to repair it, piston kits, valves, valve guides and seats, big end and main bearings, gaskets, Also e9 gearbox wanted or parts to repair it. Thanks Glynn raptor1000@hotmail.co.uk
  12. Glynn
    I didn't I couldn't get someone to look at it for me,and getting it back would be a pain.
  13. Glynn
    Thanks kristian I will see if someone can check and buy for me.
  14. Glynn
    Hi costin you said you sleeved yours do you know the diameter inner and outer of the sleeve?
  15. Glynn
    Hi what is the largest anyone has rebored the ed engine? Or has anyone skimmed the block to 5mm shorter than standard? Thanks
  16. Glynn
    Hi all my engine has big problems, it stopped running on one cylinder and started smoking on overrun .i did a compression test and five very low and one zero. I had a look up the inlet tract and found the valve is cracked. So I took the head off and the bores look worn as well. So my question is . Does anyone know a source for spares Ie valves and Pistons head gasket etc. Are there any other trucks/cars with similar parts? Or does anyone have a good engine for sale? Or which other engines are an easy fit? Thanks
  17. Glynn
    Thanks Mick That's brilliant
  18. Glynn
    Thanks all, I removed the spare wheel and there is the sender. Cleaned the contacts and now it works again. For information there is a float inside the tank with an arm which turns a gear inside the tank this then turns a shaft coming through the top of the tank. Outside the tank under a metal cover is a variable resistor
  19. Glynn
    Hi costin Do you have drawings of position of the hole?
  20. Glynn
    Hi all is there an easy way to get access to the fuel tank sender in the fuel tank? Or do I have to drop the fuel tank? My sugga is in a very small garage and getting at the back is not easy. I tried removing the instrument panel with the power on (bad idea as it shorted on the isolator switch and now the fuel gauge reads full all the time) Thanks
  21. Glynn
    Volvo sugga for sale on Milweb in medium vehicles section. Volvo TP21 Sugga 1954 21 October '15 The vehicle is very close to 100% original and complete. A couple of rust issues, but easy to weld, The body is blasted outside. Runs and drives well. Sorry cannot provide a link
  22. Glynn
    Hi all has anyone replaced the headlining or green rear inner wing covering Where did you get the material from and what is the correct colour? Does anyone have pattern drawings? Thanks all
  23. Glynn
    Hi all Does anyone have a picture of the rear window winder showing the position of the window holder and the 2 slotted sliders? Or a drawing of it so I can make a new window channel? Mvh Glynn
  24. Glynn
    Awesome did you try using it? Do you have any pictures of the inlet manifold?
  25. Glynn
    Does anyone have any good drawings or information about the gengas unit fitted to military vehicles. Pictures of a sugga with one would be great. These are also called producer gas generators. Thanks
×
×
  • Skapa nytt...